ETC 101      Fundamentals of Electrical and Computer Engineering Technology (4)

Introduction to basic circuit laws and analysis, transient circuits and first order circuits. Introduction to electronic devices and linear electronics. Examine the concepts of power systems, programmable logic controllers, and transistor switches. May not be taken for credit by graduates of associate degree programs in electrical/electronic or computer engineering technology. Three hours of lecture and two hours of laboratory per week. Corequisite: MAT 120 or equivalent or permission of instructor. Cross-listed with CET 101.

 

ETC 102      Electric Circuits (4)

Units and definitions. Ohm’s Law and Kirchhoff’s Laws. Analysis of resistive circuits. Circuit analysis using superposition, nodal and mesh methods, Norton Thevenin theorems, and current and voltage divider rules. Transient and sinusoidal steady state response of circuits containing resistors, capacitors, and incutors.   Three hours of lecture and two hours of laboratory per week. Cross listed with CET 102.

 

ETC 103      Electronics I (4)

Introduction to semiconductors, conductors, and insulators. Analysis of transistors, diodes, and their related application in rectifier and amplifier circuits. Wave‑form interpretation, AC‑DC load lines, biasing techniques, small signal amplifiers, and h parameters. Three hours of lecture and two hours of laboratory per week. Prerequisite: ETC 102 or permission of instructor.  All students who have an EET associate degree may not enroll in this course for credit. Cross listed with CET 103.

 

ETC 203      Electronics II (4)

Introduction to operational amplifier circuits incorporating feedback.  Amplifier configurations, feedback amplifiers, applications of Op‑Amps in analog computers, and active filters. Three hours of lecture and two hours of laboratory per week. Prerequisite: ETC 103 or equivalent or permission of instructor.  All students who have an EET associate degree may not enroll for this course for credit. Cross listed with CET 203

 

ETC 210      Digital Systems I (4)

Fundamentals and advanced concepts of digital logic. Boolean algebra and functions. Design and implementation of combinatorial and sequential logic, minimization techniques, number representation, basic binary arithmetic and finite state machines. Logic families and digital integrated circuits and use of CAD tools for logic design. Prerequisite: ETC 102 or equivalent or permission of instructor.  All students who have an EET associate degree may not enroll in this course for credit.  Cross listed with CET 210 and ECE 251.

 

ETC 215      Sustainable Energy Systems (2)

An introduction to sustainable energy systems.  Topics include solar energy, wind energy, fuel cell technology, biomass energy, geothermal energy, clean coal technology, ocean energy, hydroelectric power, and nuclear power.  Two hours of lecture per week.  Cross-listed with CTC 215 and MTC 215.

 

ETC 216      Electronic Communications I (4)

Introduction of analog electronic communication systems. Study of power measurements, signals, signal analysis, and signal generation. Focus on analog communication systems including amplitude modulation, frequency modulation, phase modulation and single sideband. Introduce the concepts of data communications and networking and study the public telephone network. Three hours of lecture and two hours of laboratory per week. Prerequisite: ETC 102 or equivalent or permission of instructor.

 

ETC 265      Digital Systems II (4)

Study of Digital Systems Design using the Intel family of microprocessors and their peripheral support integrated circuits. Incorporate Intel assembly language to develop programs to run the Intel hardware. Devices studied include the 8255A PPI and 8251 PCI. Design and implementation of Intel hardware and software will be emphasized. Interfacing and testing of the computer’s internal buses using logic analyzers and other test equipment will also be included.   Three hours of lecture and two hours of laboratory.  Prerequisite:  ETC 210 or equivalent.  Cross listed with CET 265.

 

ETC 288      Alternative Energy (2)

Principles and techniques associated with the methods of energy extraction from solar, wind, geothermal and biomass sources. Power management, economic development and environmental considerations will be discussed.

 

ETC 290      Introduction to Nanotechnology (3)

An introductory course covering fundamentals of nanotechnology and its applications.  Course content will cover diverse nanosystems including carbon nanotubes, semiconductor quantum dots, nanosensensors, molecular nanomachines and nanomedicine. Prerequisite: One course in Physics or permission of the instructor.  Cross listed with MTC 290.

 

ETC 299      Quality Control and Workplace Issues (2)

To provide a broad educational understanding of the impact of engineering solutions in a global and societal context along with a knowledge of contemporary issues and career opportunities.  Also, focus will be placed on the process controls necessary for the practice of electrical and computer engineering.  Cross listed with CET 299.

 

ETC 300      Tools in Technology (2)

Introduction to the field of CAD (Computer Aided Design) in the electrical engineering technology field.  Will cover the proper design of schematic drawings and the techniques of designing printed circuit boards.  Prerequisites: ETC 102 and ETC 110 or equivalents.

 

ETC 308      Electrical Power Systems I (2)

Fundamentals of power system analysis and design will be studied. Both the theory and modeling of power systems will be covered. Topics include power transformers, transmission-line parameters, steady-state operation of transmission lines, power flow and power system controls. Two hours of lecture per week. Prerequisite: ETC 102 Corequisite: MAT 230.

 

ETC 316      Electronic Communications II (4)

Study of communication signals, digital modulation techniques, telephony, digital, RF and cellular communications. Optical fiber and satellite communications are also introduced.  Prerequisite: ETC 216 or equivalent.

 

ETC 330      Assistive Technology (2)

Introduction to the fundamentals of assistive technology for people with physical disabilities. Rehabilitation engineering with an emphasis on mechanical devices used to enhance mobility and manipulation, improving physical interaction with the environment. Topics include: prosthetics, manual wheelchairs, power wheelchairs, and alternative methods for computer access. Two hours of lecture per week. Cross listed with MTC 330.

 

ETC 331      Control Systems (4)

Basic control systems studied using Laplace transforms.  Principles of electro‑mechanical control systems (electrical and mechanical), measuring means, components and their characteristics, and controller characteristics.  Analysis of a control system by the frequency/phase responses and stability criteria.  Three hours of lecture and two hours of laboratory per week.  Prerequisite: ETC 104 or equivalent.

 

ETC 342      Microprocessor and Embedded Systems Programming and Design (4)

Programming and microprocessor for embedded systems application.  Includes an introduction to interfacing components and hardware of the microprocessor.  Three hours of lecture and two hours of laboratory per week.  Prerequisite: ETC 110 or permission of instructor.  No prior microprocessors background needed.  Cross listed with CET 342 and ECE 252.

 

ETC 345      Sequential Logic Design (4)

Introduces advanced sequential logic design through the use of hardware description languages. Students will obtain hands-on experience about digital systems in Hardware languages such as Verilog and VHDL. FPGA will be extensively used in the lab. The functionality, limitations, and usage of standard sequential components and PLDs will be discussed. Various CAD tools will be used for modeling, synthesizing and implementing a several digital systems. Three hours of lecture and two hours of laboratory per week. Prerequisite: ETC 210 or equivalent. Cross listed with CET 345.

 

ETC 355      Introduction to Nanosystems VLSI (4)

Introduces CMOS devices and manufacturing technology. CMOS logic gates and their layout will be introduced. Propagation delay, noise margins, and power dissipation will be studied. Studies will gain knowledge on memory design. Various CAD tools will be used. Four hours of lecture per week. Prerequisite: ETC 210 or equivalent. Cross listed with CET 355.

 

ETC 356      Programmable Controllers (2)

Use of programmable controllers to create relay logic ladder diagrams for the development of control systems.

 

ETC 391      Fiber Optics (4)

Principles and analysis of fiber optic components and systems, fiber optic sensors, integrated optoelectronics and applications of fiber optics in telecommunications and instrumentation.  Three hours of lecture and two hours of laboratory per week.   Prerequisite: One physics course with optics and/or permission of the instructor.

 

ETC 392      Fundamentals of MEMS(Microelectromechanical Systems) and NEMS(Nanoelectromechanical Systems) (2)

Introduces the student to the emerging field of microelectromechanical systems (MEMS) based nanotechnology.  Topics will include introduction to nanonscale systems, methods of fabrications and packaging of MEMS, principle of microactuation, visualization and applications of nano and micro systems.  Prerequisite:  One course in Physics or permission of the instructor.  Cross listed with MTC 392.

 

ETC 416      Data Communication & Computer Network Technology (4)

The principles and techniques of data and computer communications are covered in detail in this course.  Topics include principles of data transmission, data encoding, digital communication techniques, transmission codes, error detection and correction, protocols, communication networks, interfacing and architecture.  Three hours of lecture and two hours of laboratory per week. Cross listed with CET 416.

 

ETC 419      Satellite Communication (2)

Principles of satellite communications, techniques of transmitting speech, data and video using satellites.  Prerequisite: ETC 316 or permission of instructor.

 

ETC 421      Wireless Communication Systems (4)

Study of the theory and the techniques used in the implementation of wireless communication systems.  Principle and analysis of mobile communication systems, wireless LAN, personal communication networks and Land-Mobile/satellite communications systems are also included.  Prerequisite:  ETC 316.

 

ETC 423      Microprocessor Interfacing (4)

Analysis of microprocessor interfacing with operational hardware. Three hours of lecture and two hours of laboratory per week. Prerequisites: ETC 110 or equivalent and ETC 342 or permission of instructor.  Cross listed with CET 423.

 

ETC 429      Microprocessors, Microprogramming and Computer Architecture (4)

Design of microprocessor and computer central processing units.  Stresses the architecture and microprogramming of the processor.  Three hours of lecture and two hours of laboratory per week.  Prerequisite:  ETC 110 or equivalent or permission of instructor.  Cross listed with CET 429.

 

ETC 431      PC Integration and Maintenance (4)

This course stresses the architecture and design of personal computers and emphasizes the use of diagnostic hardware and software to evaluate PC systems in actual lab situations.  Two hours of lecture and four hours of laboratory per week.  Prerequisite: ETC 311 or ETC 342 or CS 220.  Cross listed with CET 431.

 

ETC 433      Automatic Control Systems (4)

Transfer function approach to the analysis and design of feedback control systems. Use of Bode diagrams, and root locus plots to predict system performances. Analog and digital simulation of industrial control system problems.  Prerequisite: ETC 331 or equivalent.

 

ETC 435      Digital Control and Robotics (4)

Discrete time systems and transform sampling and reconstruction, state‑space technique and digital stimulation, stability of digital control systems, digital filtering and digital compensator design, discrete‑time optimal control, and applications in robotics.  This course is the capstone for the control emphasis which requires working on a team project using a robot arm in place of the laboratory, with an oral and written presentation at the end.  Three hours of lecture and two hours of laboratory per week. Prerequisites: ETC 331 and one course in computer programming.

 

ETC 437      Digital Filters (4)

Review of discrete‑time linear systems and random processes, z‑transforms, difference equations, and state‑space formulations. Discrete Fourier analysis and FFT algorithms, including discussions of recursive and non‑recursive filter transformations, FIR transversal and Kalman filters.  Three hours of lecture and two hours of laboratory per week. Prerequisite: MAT 122.

 

ETC 444      Special Topics in Microprocessor/Digital (Variable 1-4)

Seminar on the state‑of‑the‑art in microprocessor and digital techniques.  Topics will vary as technology changes. May be taken more than once for credit provided topics are different. Prerequisite: ETC 110 or equivalent or permission of instructor.  Cross listed with CET 444.

 

ETC 445      System-on-Chip Embedded Systems I (4)

Introduces advanced digital design through the use of hardware description languages for the specification, simulation and synthesis of complex digital systems Students will obtain hands-on experience about System-on-Chip embedded systems. FPGA will be extensively used in the lab. Either Verilog or VHDL, the two most widely used digital modeling languages for the description of digital systems at the board and component level will be studied. Structural (device interconnection), dataflow (register transfer level) and behavioral (algorithmic) models will be utilized. Various CAD tools will be used for modeling, synthesizing and implementing a several digital systems. Three hours of lecture and two hours of laboratory per week.  Prerequisite:  ETC 342 or ETC 265 or equivalent. Cross listed with CET 445.

 

ETC 446      Programmable Logic Devices (4)

Synchronous sequential circuit design. Algorithmic state machine method; state reduction; control-data path circuit partitioning. Design of sequential arithmetic circuits. Memory interfacing; bus-based design. Specification and synthesis of digital systems using hardware description language and implementation using programmable logic devices. Simulation, analysis, testing, and verification of digital systems. Cross-listed with ECE 351. Prerequisite: ETC 210 or equivalent.

 

ETC 466      System-on-Chip Embedded Systems II (4)

Hardware and software concepts in the design and analysis of embedded systems will be covered. Memory types and peripheral interfaces used in embedded systems will be considered. Performance analysis of embedded systems design will be studied. Design tradeoffs made by different models of embedded systems will be identified. Students will obtain hands-on experience about System-on-Chip embedded systems. FPGA will be extensively used in the lab. Either Verilog or VHDL, the two most widely used digital modeling languages for the description of digital systems at the board and component level will be studied as well as C programming language. Three hours of lecture and two hours of laboratory per week. Prerequisite: ETC 445 or equivalent. Cross listed with CET 466.

 

ETC 480      Electrical Technology Senior Project I (2)

This is the first of two two‑credit courses which must be taken as a pair.  Extensive investigation, preparation, and development of a design project incorporating concepts from senior level courses.  A written report is required.  At the end of first semester, student should have all information and material required to complete the project in the following semester.

 

ETC 481      Electrical Technology Senior Project II (2)

This course involves the full implementation, testing, troubleshooting, and final demonstration of the senior project as proposed in ETC 480. An updated final report shall also accompany the final project. Note: Credit given only if ETC 480 has been successfully completed. Prerequisite: ETC 480.

 

ETC 483      Optical Communications (4)

Principles and techniques associated with the transmission of optical radiation in waveguides (fibers) and free space, low and high power optical sources, internal (direct) and external (indirect) modulations.  Fiber optical waveguide and characteristics of free space, homodyne and hetrodyne detection, and design of optical communication systems. Three hours of lecture and two hours of laboratory per week.  This is the capstone course for the concentration in communications and requires working on a team project in place of laboratory assignments with oral and written presentation at the completion of the project.  The written report will include analysis, design and management of the project.  Prerequisite: ETC 391 or permission of instructor.

 

ETC 490      Special Topics in Communication Technology (2)

An in-depth study of topics selected from and based on new developments in communications technology and related areas.  Topics may include areas of secure communications, mobile communications, image transmission and optical signal processing, computer-aided design, analysis of communications links and networks and integrated services digital network standards.  Prerequisites:  ETC 316 and permission of instructor.

 

ETC 491      Independent Study (Variable 1‑4)

Extensive study of a particular topic of student interest under the supervision of a faculty member.  The student is required to submit a written proposal which includes a description of the project, its duration, educational goals, methods of evaluation, and number of credits to be earned.  Prerequisites:  Matriculated students only, permission of instructor and dean of subject area.

 

ETC 494      CO‑OP Assignment (Variable 2 or 4)

Provides 14 weeks of supervised experience in an industrial or government installation applying technology knowledge towards the solution of engineering technology problems and developing abilities required in the student’s career.  At least two reports and two supervisors’ evaluations are required.  A minimum of 60 contact hours of industrial work is required per credit hour.  May be taken repetitively up to a maximum of four credits.  Prerequisite: Permission of employer and dean.

 

ETC 495      Nanotechnology Research (3)

This course introduces students with the scientific, technical and methodological aspects of nanotechnology research.  Students will be required to work either individually or in a group on a research project and integrate knowledge of their majors into the evolving field of nanotechnology.  Emphasis is placed on addressing interdisciplinary, economical, ethical, and environmental aspects of nanotechnology.